Solar Power System (pre-2025)
Product manual for the MODULAIR Solar Power System (pre-2025).
Product Name
Solar Power System
SKU(s)
MOD-SOLAR-KIT
94Wh Li-Ion battery with 20W solar panel
1. Introduction and Specs
The MODULAIR Solar Power System is a plug-and-play solar power and battery combination that allows off-grid use of MODULAIR and MODULAIR-PM products.
This product is no longer manufactured or sold by QuantAQ as of November 2024. This manual is here for current customers and historical records only.
1.1 Specifications
Battery Capacity
26,800 mAh, 94 Wh
Battery Output
5V, 2A
Battery Type
Lithium Ion
Solar Panel
20W, 6V
Operating Range
-15ºC to 60ºC Safe charging range: 0ºC to 45ºC Safe discharging range: -15ºC to 60ºC
1.2 Certifications
The underlying batteries (manufactured by Voltaic Systems, NY) are certified to:
UN 38.3
IEC 62133
CE
FCC
2. Installation and Hardware Setup
2.1 Required Tools
2.2 What's Included?
Battery in Hammond waterproof case
Solar Panel Mounting Bracket
Battery Box Mounting Bracket
4' Extension cable for solar panels
20W Solar Panel
8-32 Screw with Nut
ETFE Panel Screw and Nut Set
1.5" U-Bolt with Mounting Plate
1" U-Bolt with Mounting Plate
2.3 Mounting Considerations
The Solar Power System includes 1" and 1.5" U-Bolts for mounting both the Battery Bracket and Solar Panel Bracket to a pole or post, but you can use whatever suits your specific mounting needs. The Solar Power System is designed to be mounted to a tripod or circular fence post but can be easily adapted for alternative installations.
It is important to ensure the orientation of the Solar Panel is optimal for your geographic location. If in the northern hemisphere, your panel should be installed facing true south, and if in the southern hemisphere, it should be mounted true north. The panel should be mounted at an angle of between 30 and 45 degrees to optimize charging.
As shipped, our Solar Panel System is optimized to be mounted of poles with diameters between 1.5” to 2.25”.
2.4 Installation
2.4.1 Mount the Solar Panel to the Solar Panel Bracket
The first step is to mount the 20W solar panel to the Solar Panel Bracket. Remove the plastic covering from the face of the solar panel and align them so that five mounting holes align with the holes in the bracket. Use the panel mounting screws (Bag 2) to secure the solar panel to the bracket.
2.4.2 Mount the Battery to the Battery Bracket
Use the four 8-32 screws and nuts (Bag 1) to secure the battery box bracket to the battery box.
2.4.3 Attach the Solar Panel Cable
Attach the 4' extension cable and attach the end of the cable to the available power input connection on the left-hand side of the base of the Battery Box. At this point, the Solar Panel is connected to the Battery and is ready to mount. Note: make sure the cable is fully inserted into its mate to ensure a good connection and to keep it waterproof.
2.4.4 Mount the Assembly
The final step is to mount the Solar Power System to a tripod, pole, or post. The 1" and 1.5" u-bolts provided in the shipment are one option. If these are not compatible with your specific mounting scenario, additional U-bolts or hose clamps should be obtained.
Reference the bracket dimensions in the Appendix to choose the best mounting hardware for your use case.
Upon mounting, orient the Solar Panel such that sun exposure is maximized (i.e. South facing if in the Northern Hemisphere). Double-check that the solar panel power cable connections are secure and connect the USB-C power cable on the right-hand side of the battery box to your MODULAIR or MODULAIR-PM system.
3. Appendix
3.1 Dimensions
3.1.1 Solar Panel Bracket
The mounting area of the solar panel bracket is designed to fit as many possible mounting configurations as possible. Each slot is 10 mm in diameter and ranges from 21 mm to 29 mm in width from center to center. There are also two mounting holes for screws that are each 5 mm in diameter and located 38 mm apart from one another vertically. The two slots in the vertical center of the bracket are each 29 mm by 10 mm and fit U-bolts that can range from 27-85 mm in width. The four vertical slots are each 21 x 10 mm and are placed 75 mm apart horizontally and will fit U-bolts between 25 mm and 67 mm.
The technical drawing for this bracket can be found on the manufacturer’s website here.
3.1.2 Battery Pack Bracket
Dimensions for the battery bracket are in mm. There are three sets of mounting slots for the U-bolts and/or hose clamps to go through. They are centered at 1", 2", and 3.5" apart from one another. They are all 0.55" tall → hose clamps that have a width of 0.5" or less will easily fit.
Last updated
